Ship From EU/UK V10.95 Launch X431 GIII X-PROG 3 Immobilizer Key Programmer With EEPROM Adapter Support X431 V, X431 V+, Pro5, Pros, Pro3S, X431 PAD V, PAD VII

Product Description

• Ship From EU/UK, fast delivery, Free tax !
• LAUNCH Official authorized dealer, 100% original
• Supported brands: VW, Audi, Skoda, Seat, BMW, Mercedes-Benz, Mini and more continue to be updated.
• X-431 GIII X-PROG 3 advanced immobilizer & key programmer is a powerful chip reading device that can read and write keys to the vehicle. 
• Supported models: 60+ brands in America, Europe and Asia. Supported systems: Automatic Transmission, Instrument System, CAS, Body System, Lock System, etc. More models and systems continue to be updated.
• Compatible with Multiple X-431 Series Diagnostic Tablet (PRO Elite, X-431 V, X-431 V+, X431 Pro5, X431 ProS, X431 Pro3s+, X-431 PAD V, X-431 PAD VII, Immo PAD, Immo Pro, Immo Plus, Immo Elite, X-DIAG Pro3 etc)

• Supports MQB
• Update VAG MQB NEC35XX add key & all keys lost NEW!!!
• All-in-One Key Programmer. Integrates Multiple Function Models
• Reads & Writes Most Engine/ Gearbox ECUs Without Disassembling the Shell
• Supported systems: Automatic Transmission, Instrument System, CAS, Body System, Lock System, etc.
• Supports VW/ AUDI MQB Platform Engine ECU Replacement or Cloning (Read engine ECU data directly from the key).
• Works with Reprogramming Device to Backup/ Restore Programming Data (For Bosch/Siemens engine ECU).
• Update VAG MQB NEC35XX D70F3524, D70F3525, D70F3526, D70F3529, D70F3532, D70F3537 add key & all keys lost NEW!!!
• X-PROG 3 enables reading and writing EEPROM, on-board MCU and BMW CAS4+/FEM chips, Mercedes-Benz infrared keys, generating special keys, reading BMW engine INS code.
• X-PROG 3 enables anti-theft type identification, remote control matching, key chip reading and matching, anti-theft password reading and anti-theft component replacement.

•  You can buy MCU3 Adapter  to do Benz All Keys Lost and ECU TCU Reading.
• X-prog3 will program IMMO keys for German makers only. If you want to do advanced key programming, you need to Activate the Authorization of IMMO package.
• To check detail X-PROG3 Immobilizer key programming list, check list on the official website: https://qcar.x431.com/newqcar/carDes?lan=EN&swId=RESETPROG&page=1&type=3&serialName=Immo Program&area=RESET
• LAUNCH X431 X prog 3 Compatible with (X-prog 3 can't work alone) : X431 Diagun V , X431 PRO MINI , X431 PROS MINI, X431 V , X431 PRO3S+, X431 V+ , X-431 PRO GT, X-431 PRO V4.0, X-431 PRO 3 V4.0, X-431 PRO 5, X-431 PAD III V2.0, X-431 PAD V, X-431 PAD VII

Update Notice: 

V11.00
1)Added the vehicle mode for the VW IMMO software.
2) Optimized the anti-theft system automatic identification function for the VW anti-theft software

V10.95 (Feb 28th, 2024)

Added read and write function for a total of 48 Renesas model RH850_ encryption single-chip computer.

Added readout function for 13 VW IMMO MOB instrument,
Added IMMO readout all missing function for VW, added image zooms in/out function,
Added OBD pre-process function for BMW FEM/BDC immo system.
Optimized PIN CODE, CS code and VIN code input box function, optimized file save function, optimized online backup/restore function.

Optimized read and write function for Porsche front terminal/rear terminal electrical module,
Optimized key learning. Read-out preprocessing function for BMW FEM/BDC IMMO system;
Fixed ECU read and write function for Bosch MD1XX/MG1XX SPC main control unit,
Fixed the issue of some ME17.8.8 engine ECU not connected,
Fixed the issue of some SMART/Mercedes-Benz W204/W207/W212 steering lock not start after replacement

1) Added a total of 48 RH850_encrypted single-chip machine read and write functions,
including R7F701008, R7F701011, R7F701016, R7F701021, R7F701OO9, R7F701012, R7F701017, R7F701022, R7F701026, R7F701002, R7F701010, R7F701013, R7R01018, R7F701023, R7F701027, R7F701014, R7F701019, R7F701024, R7F701028, R7F701032, R7F701040, R7F701042, R7F701044, R7F701046. R7F701050, R7F701003, R7F701015, R7F701020,R7F701025, R7F701029, R7F701033, R7F701041, R7F701043, R7F701045, R7F701047, R7F701051, R7F701030,R7F701034, R7F701048, R7F701052, R7F701054, R7F701056, R7F701006, R7F701007, R7F701049, R7F701053

2). Add a total of 13 VW IMMO MQB instrument read-out functions, including D70F3524, D70F3525_V1, D70F3525_V2, D70F3525_V3, D70F3525_V4, D70F3526_V1, D70F3526_V2, D70F3526_V3, D70F3526_V4, D70F3529, D70F3532_V1, D70F3532_V2, D70F3537

Jan. 2024.
Adds MQB calculator. Obtain sync data for free.
Need 
Instrument panel CS code 16 bytes
Ecu 16 bytes CS code
Tcu 16 bytes CS code
ELV 16 bytes CS (if present)

April 2023
1. Add CAS2, CAS3/3+ IMMO system file generated key function, supported to acquire EEPROM after CAS module read and generate dealer key using EEPROM file
2.FRM module replacement, add FRM module data function, supported to download FRM module data with internet connection.
3. Adds OBD preprocessing function for BMW BDC IMMO system (program BMW BDC key via OBD)

New Software Update V10.80 (May 25th, 2023)

1. Added the key learning and instrument replacement functions for Johnson Control MQB instruments (including chips A2C81589600, A2C81589700, D70F3526, and D70F3529).
2. Added the key learning, all keys lost, and instrument replacement functions for Johnson control instruments as of year 2014
3. Added the instrument cloning function for VDO NEC 35XX MQB instruments (including chips A2C81 589600, A2C81 589700, D70F3526 and D70F3529)
4. Added the functions “All Keys Lost” and instrument replacement for the fourth-generation 35XX instruments.

The Launch X431 GIII Software Update function keeps your diagnostic software & app up-to-date, you can also use it to customize your frequently used software. As a powerful chip reading and writing device, it’s compatible with most X431 series tablets like X431 V+, X431 PAD VII, X431 PRO5, etc.

How to update X-PROG 3 diagnostic software & APP?

1. On the main diagnostic scree, tap “Software Update” to enter the update center. Check the software you want to upgrade, and then tap “Update”.

2. Once downloading completed, the software packages will be installed automatically.

3. You will see below dialogue box once the installation is completed.

Note:

• You may stop the process by tapping “Stop”, and tap “Continue” to resume the process later.
• In case of network connection failure, tap “Retry”.

• Supported brands: VW, Audi, Skoda, Seat, BMW, Mercedes-Benz, Mini and more continue to be updated.
• Supported models: 60+ brands in America, Europe and Asia. Supported systems: Automatic Transmission, Instrument System, CAS, Body System, Lock System, etc. More models and systems continue to be updated.

• Read BMW engine ISN code.
• Read/write BMW CAS4+ and FEM chips.
• Read/write Audi fifth-generation steering column chips
• Read/write EEPROM.
• Read/write MCU.
• VW Fourth-generation Dump Mode All Keys Lost.
• Read engine in BENCH mode.
• Read gearbox data.
• Supports VW/AUDI MQB platform engine ECU replacement or cloning (Read engine ECU data directly from the key).
• Supports VW/AUDI MQB platform gearbox ECU replacement or cloning.
• Supports ECU replacement for the fifth-generation of Audi (0AW/0B5) gearbox.
• Supports reading, writing & cloning the ECU for the fourth-generation of VW UDS engine.
• Supports BMW E chassis 8HP gearbox ECU reprogramming to empty.
• Works with reprogramming device to backup/restore programming data (For Bosch/Siemens engine ECU)

• Supports the BMW F and G chassis 8HP gearbox ECU reprogramming to empty.
• Supports the BMW CAS4/CAS4+ module replacement.
• Supports the ECU cloning and replacement for BMW Siemens engines.
• Supports ECU replacement for the fourth-generation of VW/AUDI engine;
• Supports ECU replacement for the fifth-generation of VW/AUDI Bosch and Siemens engines.
• Supports the all lost and replacement for the fourth generation of AUDI EZS, comfortable ECU, and KESSY IC.
• Erase the password for Mercedes-Benz engine and gearbox within 3S.11. Add the function of calculating the password for the Mercedes-Benz key within 1 minute.
• Integrated the functions of key matching/copy, anti-theft IC reading & writing, and ECU reading & writing, etc.
• Supports common ECU/MCU/EEPROM major manufacturers, with over 1200 product models, and constantly updating.
• Supports ECU replacement for all lost without disassembly for VW/AUDI non-35XX instrument (it can be read directly through independent harness without removing the IC).

Supported Chip Brands:
It supports common mainstream ECU MCU manufacturers, with more than 1,000 product models, and they are continuously being updated.

Atmel	NSC
Fujitsu	Philips
Infineon	Renesas M16
MC68HC05	Renesas M32
MC68HC08	Renesas M32R
MC68HC11	Renesas M32C
MC68HC12	Renesas R8C
MediaTek	Renesas V850 SPI
MicroChip	Renesas V850 UART
Nordic	Samsung
ST	SiLabs

Supported EEPROM Brands:
It supports common mainstream EEPROM manufacturers, with nearly 1,000 product models, and they are continuously being updated.
 

4Wire	GI	Numonys	SST
Adesto	GigaDevice	OKI	ST
AKM	Grundig	ON Semi	Toshiba
Altera	HOLTEK	Other	Winbond
Amic	Hynix	PCT	Xicor
Atmel	I2C	Philips	xUSSR
BOSCH	ITT	Pioneer	YMC
Catalyst	KHIC	PMC	Spansion
Chings	Macronix	Ramtron	SPI
Dallas/Maxim	MicroChip	Rohm	NEC
EON	Micron	Samsung	NSC
ESMT	MicroWire	Seiko	Ford
EXEL	Mitsubishi	Siemens	Fujitsu
Fairchild	Motorola	Sony

X-prog3 ECU TCU Clone Function Only with high-end tablets (PAD5, PAD 7, PRO5, IMMO PLUS etc)




How to Use X-PROG3 to Read and Write Data?


Connection method 1: Directly connect to OBD16 for key matching, data reading and writing, etc

Connection method 2: Place the anti-theft EEPROM or MCU chip in the chip burning socket, and then insert the chip burning socket into the slot of the immobilizer programmer locker and lock it to realize the data interaction between the IC anti-theft chip and the diagnostic host

Connection method 3: After removing the ECU from the car, connect the anti-theft ECU pin to the DIY slot of the immobilizer programmer through the cable to realize the data interaction between the anti-theft ECU and the diagnostic host.

Launch X431 X-PROG vs. X-PROG3

Item	Launch X431 X-PROG	Launch X431 X-PROG3
Read/Write EEPROM	No	Yes
Read/Write MCU	No	Yes
Mercedes Benz Keys	No	Yes
Key simulator	No	Yes
VW 4th IMMO Dump Mode All Keys Lost	No	Yes
Read engine in Bench mode	No	Yes
VW 4th IMMO enumeration all keys lost	No	Yes
Read gearbox data	No	Yes
Read and write keys	Yes	Yes
Read BMW engine ISN code	No	Yes
Replace OBD reading component	Yes	Yes
Read & Write BMW CAS4+ and FEM chips	No	Yes
Read engine in Boot mode	No	Yes
Read & Write Audi 5th generation steering column chips	No	Yes

Specification:

Interface	DB26, DB15
Input Power	DC12V
Working CurrentMax	500mA
Power Consumption	5W
Storage Temperature	-20℃~70℃
Working Temperature	0℃~50℃

Package List:
1pc x Launch X-PROG 3
1pc x Power adaptor
1pc x Main diagnostic cable
1pc x The fourth-generation data acquisition cable
1pc x The fourth-generation of EEPROM data acquisition cable(without dismantling dashboard)
1pc x BENCH mode cable
1pc x MCU converter V1
1pc x MCU converter V2
1pc x MCU cable with multiple leads
1pc x EEPROM chip adaptor
1pc x Benz infrared analog acquisition key
1pc x MCU cable with multiple leads
1pc x EEPROM converter
1pc x User Manual 

Ship from EU/UK/Other Overseas Warehouse

• Normally take about 3-5 working days to arrive
• Valid for EU/UK Local Address Only - Only Item title marked "EU/UK SHIP" will ship from EU/UK warehouse!
• EU Warehouse was located in Germany/Czech and it only can ship to EU country: 
  Germany, France, Spain, Netherlands, Finland, Sweden, Austria, Belgium, Bulgaria, Croatia,
  Czech Republic, Denmark, Estonia, Greece, Hungary, Ireland, Latvia, Lithuania,Luxembourg,
  Malta, Poland, Portugal, Republic of Cyprus, Romania, Slovakia, Slovenia 
• Note: If EU/UK Stock sold out, your order will be shipped from China via DHL or YANWEN (No Tax) by default.

• Whatsapp: +86 18054815707
• Email: sales@X431shop.eu
• Hot line: +8618054815707

Click to join the X431shop.eu Tech Support WhatsApp Group